Modular/Compact Foot Set

Back to search

Modular/Compact Foot Set

The LCP Compact Foot Set is indicated for phalangeal, metatarsal, tarsal, extra- and intraarticular calcaneus fractures as well as osteotomies and arthrodesis in the foot.

With these additions, the LCP Compact Foot Set now offers a wide range of anatomical precontoured and adaptable plates for trauma and orthopedics in three dimensions (2.0, 2.4, and 2.7mm). The low profile design and the completely buried screw heads make the Set soft tissue friendly.

Details
Instruments
Disclaimer

All plates of the Compact Foot Set are now available as Locking Compression Plates (LCP) with the advantages of reduced primary and secondary loss of reduction, reduced pull-out of screws, less periosteal compression, better hold in osteoporotic bone, more stable fixation, and bridging of fragments. All plates are available in titanium and stainless steel.

The LCP Compact Foot Set comes in a modular structure. Separate Vario cases for forefoot and hindfoot surgery are offered. Color-coded instruments and modules enable easy identification in the OR.

Fig 1 LCP Foot Plates

Fig 2 LCP Foot Plates

LCP Plate 2.0 and 2.4, straight, 48 holes, TiCP

These plates correspond to the respective former LC-DC plates, thus are intended for the same indications, including the new features of the combi-hole/locked screws.

LCP Plate 2.0 and 2.4, straight, 48 holes, TiCP

LCP Plate 2.7, straight, 412 holes, TiCP

Particularly for metatarsal shaft fractures and correcting osteotomies of the first ray.

LCP Plate 2.7, straight, 412 holes, TiCP

LCP Condylar Plate 2.7, TiCP

Metatarsal fracture fixation especially in the metaphyseal zone and close to a joint.

LCP Condylar Plate 2.7, TiCP

LCP T-Plate 2.7, 3 & 4 holes, TiCP

Particularly for medial fusions in the tarso-metatarsal area.

LCP T-Plate 2.7, 3 & 4 holes, TiCP

LCP L-Plate, oblique, 2.7, right and left versions, 3 & 4 holes, TiCP

For fracture and fusion fixation, especially the proximal part of the fifth ray.

LCP L-Plate, oblique, 2.7, right and left versions, 3 & 4 holes, TiCP

LCP L-Plate, 2.7, right and left version, 3 holes, TiCP

For proximal fracture fixation of the fourth/fifth ray or fusions to the cuboid.

LCP L-Plate, 2.7, right and left version, 3 holes, TiCP

Locking H-Plate, 2.7, 5 & 8 holes, TiCP

For fixation of correcting osteotomies of the calcaneus (eg, Evans osteotomy). Calcaneal fracture fixation of the medial and occasionally lateral wall.

Fig 1 Locking H-Plate, 2.7, 5 holes, TiCP

Fig 2 Locking H-Plate, 2.7, 8 holes, TiCP

Drill Bit, with measuring scale, for Mini Quick Coupling, 2-flut, SS

The Drill Bit incorporates a measuring scale for easy determination of the screw lengths.

Drill Bit, with measuring scale, for Mini Quick Coupling, 2-flut, SS

Bending Pin for LCP Plates 2.7

A Bending Pin enables bending of the threaded round holes of the LCP Plates 2.7.

Bending Pin for LCP Plates 2.7

Hazards and labeling

Due to varying countries’ legal and regulatory approval requirements, consult the appropriate local product labeling for approved intended use of the products described on this website. All devices on this website are approved by the AO Technical Commission. For logistical reasons, these devices may not be available in all countries worldwide at the date of publication.

Legal restrictions

Any use, exploitation or commercialization outside the narrow limits set forth by copyright legislation and the restrictions on use laid out below, without the publisher‘s consent, is illegal and liable to prosecution. This applies in particular to photostat reproduction, copying, scanning or duplication of any kind, translation, preparation of microfilms, electronic data processing, and storage such as making this publication available on Intranet or Internet.

Some of the products, names, instruments, treatments, logos, designs, etc referred to in this publication are also protected by patents, trademarks or by other intellectual property protection laws (eg, “AO” and the AO logo are subject to trademark applications/registrations) even though specific reference to this fact is not always made in the text. Therefore, the appearance of a name, instrument, etc without designation as proprietary is not to be construed as a representation by the publisher that it is in the public domain.

Restrictions on use: The rightful owner of an authorized copy of this work may use it for educational and research purposes only. Single images or illustrations may be copied for research or educational purposes only. The images or illustrations may not be altered in any way and need to carry the following statement of origin “Copyright by AO Foundation, Switzerland”.

Check www.aofoundation.org/disclaimer for more information.

If you have any comments or questions on the articles or the new devices, please do not hesitate to contact us.

“approved by AO Technical Commission” and “approved by AO Foundation”
The brands and labels “approved by AO Technical Commission” and “approved by AO Foundation”, particularly "AO" and the AO logo, are AO Foundation's intellectual property and subject to trademark applications and registrations, respectively. The use of these brands and labels is regulated by licensing agreements between AO Foundation and the producers of innovation products obliged to use such labels to declare the products as AO Technical Commission or AO Foundation approved solutions. Any unauthorized or inadequate use of these trademarks may be subject to legal action.